Discovering Essential Plumbing Skills is Important When Installing a Bathtub
Discovering Essential Plumbing Skills is Important When Installing a Bathtub
Blog Article
How do you really feel in regards to A Step-by-Step Guide to Installing a Bathtub?
Mounting a bath tub isn't specifically rocket science, but it does call for solid plumbing, woodworking, and often, tiling abilities. Replacing an old tub with a brand-new one is also a moderately challenging task. If the old bathtub is conveniently accessible, the project can relocate speedily; if you have to open up a wall surface to remove the old tub and also place the brand-new tub, the task is a lot harder. In either instance, the job is within a house handyman's skills, although you will require an assistant to vacate the old bathtub and also embeded in the brand-new one. Make certain you have actually certified on your own for the work and fit trying it. As opposed to working with a contractor to take over a halfway-completed project, it is better to take into consideration using one before you start. Possibilities are you might need an expert plumber to make tube links.
This article will assist you mount a brand-new tub in your bathroom if you have actually already acquired a new tub and don't need to transform the plan of your previous supply of water pipes.
Your tools and also material list need to consist of the following:
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is disconnect the water supply. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing taps can be fairly problematic because of the limited gain access to that is often the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a cloth prepared for the staying water that will certainly originate from the pipes. Once the supply pipes have been eliminated, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming throughout this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing compound.
Before moving on to fit the new taps, compare the pipe connections on the old taps to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, then you will certainly need minimizing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the faucet in the placing hole in the bath/basin ensuring that the washers remain in place in between the faucet and the sink. Protect the faucet in position with the maker given backnut. As soon as the tap is firmly in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical tap connectors. The previous type should be connected to the tap finishes initially, tightening up only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Tub
Using both wooden boards under its feet, position the bath tub in the called for setting. The wooden boards are helpful in evenly spreading the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four small points.
The next objective is to make sure that the tub is leveled all round. This can be achieved by examining the level and also changing the feet on the bathtub up until the spirit level reviews level.
To set up faucets, fit all-time low of the furthest versatile tap port to the ideal supply pipeline by making a compression sign up with; after that do the very same for the other tap.
Turn on the water as well as examine all joints and new pipework for leaks and tighten them if required. Fill up the bath tub and likewise inspect the overflow electrical outlet and also the normal electrical outlet for leaks.
Lastly, take care of the bath paneling as defined in the supplier's instruction manual. Tiling and also sealing around the bathtub must wait until the tub has actually been utilized at the very least when as this will certainly settle it into its last position.
Getting ready for the Installment
Firstly, the supporting structure provided with the bath ought to be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to ensure that if the tap comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets device to avoid strain on the bathtub.
Fit the adaptable tap connectors to the bottom of the two taps making use of 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you make use of every one of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its final position.
Tiling Around the Bath tub
In the location where the bathroom satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to fracture a stiff seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, causing difficulties with moisture as well as feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to assimilate your fixtures and also fittings. They are offered in tubes and also cartridges, and can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to always fill the bathtub with water before sealing, to allow for the motion experienced when the tub is in use. The sealant can break fairly early if you do not take into consideration this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally quickly available on the marketplace. It is suggested to fit the ceramic tiles using waterproof or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen reader on How to Install a Bathtub, I thought sharing that topic was a good thing. Remember to take a moment to distribute this blog posting if you liked it. Thank you so much for your time spent reading it.
Clog issue? Reach out! Report this page